Note
All measurements taken at maximum gain unless otherwise stated, Rs = 150Ω
RedNet R1 is designed for professionals who need to adapt their audio configurations quickly to suit the ever-increasing demands of the studio environment, and interact with their audio system like never before. Inputs from one of eight source groups (each of up to 12 channels per source, from 32 total channels) can be mixed and routed to up to 12 monitor output channels, formatted from mono through to 7.1.4 surround, providing the flexibility to monitor in a range of common setups including Dolby Atmos® and other immersive audio workflows. Alternatively, completely custom setups of up to 12 outputs can be configured for bespoke speaker configurations.
RedNet R1 can be set up to control groups of outputs from the multitude of sources and destinations available to Red interface users. From Pro Tools™ | HD and other DAWs, analogue inputs and outputs, ADAT and S/PDIF connections, and from entire Dante® audio ecosystems, audio can be switched and summed cross platforms, simultaneously and interchangeably. Top-panel control includes level, reference level preset selection, dim, mute and a variety of solo modes. There's an A/B switch for switching between monitoring presets, and up to four fold-down presets allow fast switching for checking downmixes.
RedNet R1 also features Dante-enabled talkback, an internal mic preamp for connecting an external talkback mic, built-in microphone and a high-powered headphones output, so you can monitor audio inputs and outputs, and interact with talent and other users on the system. Up to four talkback destination groups are available when used with a Red interface (when used with other Dante devices, a single talkback group is available).
Two LCDs display highly accurate level metering of the outputs, sources and headphone outputs, and provide visual cues for navigating menus. RedNet Control software is used to quickly set up both simple and complex monitoring and routing configurations. Other features include a quarter-inch jack socket, which accepts a footswitch for talkback management, LFE muting and more. RedNet R1 can be powered via Ethernet to reduce cabling complexity (using the PoE standard), or by the supplied DC power supply.
Note
All measurements taken at maximum gain unless otherwise stated, Rs = 150Ω
Gain Range
0dB to 55dB
Type
Electronically Balanced, Zin = 3kΩ
Max. Input Level
+10dBu ± 0.5dB
Note
All measurements taken at maximum gain unless otherwise stated, Rs = 150Ω
Gain Range
0dB to 55dB
Max. Input Level
+10dBu ± 0.5dB
Frequency Response
20Hz - 20kHz ± 2dB
THD + N
Less than -98dB (0.0012%) @ -1dBFS
EIN
Less than -128dBu 'A'-Weighted (typical)
Signal-to-Noise Ratio
-111dB 'A'-Weighted (typical), min gain
Common-Mode Rejection Ratio
50/60Hz CMRR: <-77dB
Type
Electronically Balanced, Zin = 3kΩ
Note
All measurements taken at +19dBm reference level, maximum gain, RL = 600Ω
0 dBFS Reference Levels
+11dBm
Frequency Response
20Hz to 20kHz ±0.5dB
THD + N
-100dB (0.001%) @ -1dBFS, Rs = 150R
Dynamic Range
108dB 'A'-weighted (typical), 20Hz - 20kHz
Noise in Presence of Signal (NiPoS)
Greater than -97 dBu 'A-Weighted'
Output Impedance
5Ω
Headphone Impedance
32Ω - 600Ω
Mic Input to Headphone Output
Less than -122dB; 20Hz - 20kHz (all other channels at 0dBFS)
Headphone Output to Mic Input
Less than -84dB; 20Hz - 20kHz (all other channels at 0dBFS)
Left to Right
Less than -85dB; 20Hz - 20kHz (all other channels at 0dBFS)
Right to Left
Less than -85dB; 20Hz - 20kHz (all other channels at 0dBFS)
Supported Sample Rates
44.1 / 48 / 88.2 / 96 kHz (-4% / -0.1% / +0.1% / +4.167%) at 24 bit
Clock Sources
Internal or from Dante Network Master
External Talkback Mic Input
1 x XLR (F)
Foot Switch
1 x 1/4" stereo jack
Headphone Outputs
1 x 1/4" stereo jack
Power Switch
1 x Switch
Talkback Gain Pot
1 x Pot
Talkback Switch
1 x Tri-State Switch (External Talkback + 48V, External Talkback and Internal Talkback)
PSU (PoE and DC)
1 x PoE Input and 1 x DC 12V Locking Barrel Input Connector
Network
1 x Standard RJ45 connector
LCD Screens
2 x Screens (Control, Status, Metering & Menus)
Control Functions
2 x Continuous Pot (Level & Dim). 1 x Pot (Headphone Output). 24 x Multi-Function Switches (Sources, Talkback, Monitor Outputs & Menu Items). 12 x Single-Function Switches (Headphones, Sum, Spill, Mode, Mute, Solo, Outputs, A/B, Cut x 2, Dim & Output Lock)
Power over Ethernet (PoE)
Complies with IEEE 802.3af class 0 Power-over-Ethernet standard (PoE A or PoE B compatible)
DC Power Supply
1 x 12V 1.2A DC Power Supply
Power Consumption
PoE: 10.3W - DC: 9W (When using supplied DC PSU)
Operating Temperature
Operates at up to an ambient temperature of 40 degrees Celsius